0-10V Analog Interface with 24V relay

This interface is designed to manage the signals on a 0-10V scale, and the instructions / status on 24V relay interface.

MAIN SPECIFICATION

The power supplies can be remotely controlled through a 0-10V analogue interface. The interface consists in a single DB-25 connector, located on the rear panel of the power supply. With this option, the instructions and statuses are managed through a 24V relays.

The remote control cable must be shielded, and we recommend to install a length shorter than 3m.

Detailed specification

 

Pin
Signal
Signal description
I/O
Impedance
1
HV-Off control
Activated by a fleeting opening of the +24V
input
2
Fault status
Internal fault: Open contact = An internal fault has been detected; +24V = No fault
output
3
Interlock status
Open contact = External interlock is open; +24V = External interlock is closed
output
4
HV-On control
Activated by a fleeting closing to +24V
input
5
Output voltage measurement
0V  to 10V = 0% to 100% of max output voltage
output
475 Ω
6
Output current measurement
0V  to 10V = 0% to 100% of max output current
output
475 Ω
7
Inhibit control
Activated by a digital signal between +5V to +24V
input
8
Remote control
Open contact = Local control mode; +24V = Remote control mode
input
9
External 24V reference
24V reference voltage, must be supplied by the user.
input
10
Interlock status (active low signal)
Open contact = External interlock is closed; +24V = External interlock is open
output
11
Output power measurement (option)
0V  to 10V = 0% to 100% of max output power (option)
output
12
Local output voltage setting
Copy of the output voltage setting on the front panel potentiometer. 0V  to 10V corresponds to 0% to 100% of max output voltage.
output
10 kΩ
13
Local output current setting
Copy of the output current setting on the front panel potentiometer. 0V  to 10V corresponds to 0% to 100% of max output current.
output
10 kΩ
14
Remote output current setting
0V  to 10V = 0% to 100% of max output current
input
115 kΩ
15
+10V reference
+10V reference for anologue signals, max current : 5mA
output
16
0V reference (digital signals)
0V ground reference for digital signals
output
17
Remote output voltage setting
0V  to 10V = 0% to 100% of max output voltage
input
115 kΩ
18
Regulation mode status or End of Charge status
For a DC power supply: Open contact = Current Regulation; +24V = Voltage Regulation For a Capacitor charging power supply Open contact = Capacitor is being charged; +24V = End of charge
output
19
HV-On status
Open contact = HV output is disabled (HV Off); +24V = HV output is enabled (HV On)
output
20
0V reference (analogue signals)
0V ground reference for analogue signals
output
21
HV On status (active low signal)
Open contact = HV output is enabled (HV On); +24V = HV output is disabled (HV Off)
output
22
External 24V reference
24V reference voltage, must be supplied by the user.
input
23
Fault status (active low signal)
Open contact = No fault; +24V = An internal fault has been detected
output
24
External interlock
Connect this pin to the digital to the 0V reference for digital signals (pin 16) to close the interlock.
input
25
+10V Reference or Remote output power setting (option)
Standard : +10V reference for anologue signals, max current : 5mA Option: 0V to 10V = 0% to 100% of max output power
output

24V output signals are limited to 10mA

Interfaces

Complementary interfaces
You need
informations ?
Technix
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.